A&J MARINE WELDING BRACKETS


A & J Motor Bracket

- you will see improved performance

A & J Marine Welding Florida Company builds outboard motor brackets to fit any style of vessel. Whether you have a full transom , curved or cut-out transom. A & J Outboard motor brackets serve many purposes, in many cases allows the powerboat to float higher, go faster with better balances.

A & J Motor Brackets are designed and tested to withstand the dangerous saltwater conditions. All Motor brackets are pre-drilled and available with non-skid white texture to match most boats. Custom manufactured products include, custom colors by order.

A & J have available 2 styles of brackets( a square box Standard Bracket and Floatation Motor Brackets), available is an installation kit.

All Brackets are hand welded, tailored to our exacting standards to enhance the appearance, function and ergonomics and we guarantee our top workmanship in the industry.

contacts:

A&J MARINE WELDING
7318NW 46 Street
Miami, FL 33166
Phone: 305-265-7922
Fax: 305-265-0878

web www.custommarinewelding.com


Outboard Motor Brackets, outboard jack plates & Motor Mount Accessories - installation advice, tips and guides

Outboard Motor Brackets - Garelick

Controls & Steering

Boat Accessories - Controls and Steering Cables

Outboard Motor Brackets for small sailboat with auxiliary power.

Outboard Brackets - Aluminum or Stainless Steel. The handiest way to equip a small boat/sailboat with auxiliary power - or a fishing boat/craft with a low powered trolling engine - is to mount an outboard motor on the transom by means of a retractable bracket.

Garelick - Outboard Brackets

Outboard Motor Brackets

This kind of bracket allows the boatmans to lift the motor out of the water when it is not in use without removing it from the bracket.

Contacts:

PHONE : 651.459.9795
FAX : 651.459.8269
MAILING ADDRESS
GARELICK MFG CO.
644 Second Street
P.O. Box 8
St. Paul Park, MN 55071-0008

Web: www.garelick.com

Outboard Motor Brackets

HYDRA-Powered Outboard Motor Brackets

Build and designed from over 30 years of experience in building quality Outboard Motor Brackets. This series offers the most advanced innovative features available and was tested by a leading motor manufacturer.

- Effortless operation – raises and lowers auxiliary motors in less than 20 seconds
- 12 volt self contained marinized hydraulic actuator
- Designed for 4-Stroke motors, wide stance provides stability
- Two models – handles up to 40 H.P. motors
- Heavy duty 1/2" thick 6061T6 structural aluminum extrusion
- Triple coat protective finish (anodized, E Coat, powder coated)
- Aircraft stainless steel hardware and engineered bronze bushings at pivot points for increased ease of operation and durability
- 2000 lbs.. tensile strength motor safety cable included
- 1/2 - 20 x 4 1/2" stainless steel mounting hardware included
- Wiring harness and operating control switch included


Manual Hydraulic Outboard Motor Brackets

This Outboard Brackets series offers the most advanced innovative features available and was tested by a leading motor manufacturer.

- Raise and lower trolling and auxiliary motors on power boats and sailboats with ease...Watch this video to see how easy it is!
- New generation motor bracket lifts up 4 stroke motors with short side to side movement of a lever handle (removable for stowage). This simple movement activates a marinized manual hydraulic lift pump inside the body of the bracket
- Release valve lowers the bracket down into operating position
- 14" of continuous vertical height adjustment provides optimum trim adjustment for any water surface or boat load condition
- Eliminates the inconveniences of conventional spring loaded models; no electrical wiring required
- High Tensile Alloy - Black satin Anodized aluminum body to resist corrosion
- Aircraft stainless steel hardware and engineered bronze bushings at pivot points for increased ease of operation and durability
- Heavy-Duty Stainless Steel Hardware for increased durability
- 2" Thick Poly Mounting Board
- Wide Track Design for added stability and strength
- This innovative design offers the easiest to operate manual motor bracket ever built by Garelick EEz-In
- 2000 lbs. tensile strength motor safety cable included


Aluminum Outboard Motor Brackets

FOR 2-STROKE MOTORS AND FOR 4

The original series that offers ease of operation and proven performance. Designed for lighter weight boats, lower horsepower "kicker" motors, these versatile and compact brackets have set the standard for over three decades.

for 2 STROKE MOTORS

- Retractable Bracket for Trolling Auxiliary Motors on power and sailboats with ease
- Transom mount locks and holds motor up or swings down for propulsion
- Tough alloy Anodized Aluminum frame, Stainless Steel springs
- Fits all style motors – Extra Wide 11 1/2" (29cm) Black Poly Mounting Board
- 4-position locking height adjustment
- Stainless Mounting Hardware and instructions included
- MOUNTING PAD 2" thick x 11.5" wide (5 x 29cm). Designed to accommodate the width dimensions of newer, wider style motor locking clamps

A Kicker Engine Bracket

With built-in swimsteps and stylishly sculpted transoms taking up room on today’s boats, finding a suitable flat space to hang an auxiliary outboard can be an hard.

For example: If you tried to mount a Tohatsu 18 four-stroke kicker on the back of one of our project boats, a Triton 2486 walkaround. This boat will easily hold twin engines, but the single Mercury 250 VeradoOutboard sitting in the middle of the transom left inadequate space on either side to simply hang the kicker. In addition, with a main engine shaft length of 30 inches and a 20-inch Tohatsu side-by-side, getting the kicker’s prop low enough in the water while still having room to tilt it up when not in use was an insurmountable challenge.

Garelick kicker Outboard motor brackets

Garelick provide two versions motor brackets (for 2 and 4 Stroke Motors) designed for "kicker" lower horsepower outboards. Both motor brackets are aluminuim auxilary.

Garelick kicker Outboard motor bracket model 71044 for 2 stroke Outboards kicker Garelick Outboard motor bracket model 71090 for 4 stroke Outboards

Two rudders basically - Holds the 15hp like a rock. You have the power lift on it, and have hydraulic steering going to it from the big motor so when trolling, You feel like you have more control.


Panther Marine Products kicker Outboard brackets

Hang it

This US Minnesota-based company also makes numerous bracket-mount models, transom jacks and steering devices that can simplify a challenging outboard installation. Panther Marine’s Models will worked best for these projects, but some may want to look for Motor Bracket models, designed specifically to fit the contoured transoms of Ranger and Lund Pro-V boats. Its shape may ease the installation on other boats with contoured transoms, as well.

Easy lifting motor bracket for both: with 2-stroke up to 20hp or 4-stroke motors up to 15hp

The Panther Marine Products (www.panthermarineproducts.com) hydraulic-lift model is capable of holding outboards up to 40 hp or 150 pounds, and gives you a choice of 7 or 13 inches of setback. For those boat owners with strong backs, a manual version is also available. The bracket also raises the engine several inches when it is tilted up, keeping the powerhead high and dry when not in use. When the Outboard bracket is in the down position, the prop is deep enough in the water for a good bite. Still, the installation is not totally trouble free, and some modifications still needed.
All available motor bracket models at: http://www.panthermarineproducts.com/outboard-motor-brackets.

The Drill

If your main problem is the splashwell through-hull drain, a large nylon fitting that protrud approximately 1/2 inch beyond the transom. This prevented the bracket from mounting flat against the transom. After careful measuring, you can use a hole saw and cut a 3-inch-diameter hole in the bracket, allowing it to fit flush around the fitting. This is not a structural part of the bracket and the hole does not sacrifice strength.

The key to a successful installation is to measure, and then measure again, before making cuts or drilling holes. Measure not only where the outboard bracket will go but also measure where the kicker is going to go when it is mounted on the bracket in both the up and down positions.

How to

Installing A Kicker Engine Bracket

STEP 1: A transom through-hull drain required us to cut a 3-inch hole so the bracket would fit over the drain fitting. We measured carefully so we didn’t cut through a structural part of the bracket.

Although the Panther Marine bracket includes a template for marking the mounting holes, we’re not fond of paper templates because they tend to tear and wrinkle. We found it easier to pull the hinge pin on the bracket, put the bracket in position, and then drill the holes.

STEP 2: Pulling the hinge pin (see illustration on page 72) allows the bracket to be separated enough so that you can easily gain access to mark and drill the mounting holes. Bolt the bracket to the transom with the supplied bolts and fender washers; be sure to use marine sealant to waterproof the holes.

STEP 3: Reinstall the pin and hang the engine. Be sure to drill and through-bolt the engine to the mounting bracket using the spacer block that comes with the lift bracket.

Next, mount the twin, hydraulic-lift solenoids in a protected area close to the bracket. We tucked them in on the underside of the engine well. Wiring the unit is simple, and consists of mounting the twin solenoid block for the hydraulic pump.

Two leads go to the positive and negative battery terminals, a short lead goes to the plug for the hydraulic pump on the bracket, and a long lead goes to wherever you’d like to mount the control head. Remember to disconnect the batteries before doing any wiring.

STEP 4: The Panther Marine power kicker bracket features a push-button up/down controller that can be mounted almost anywhere. We routed it under the gunwale and up to the helm.

Once we had reconnected the batteries and tested the system, we finally had a solidly mounted power-lift kicker that stores high enough to clear the boat’s molded swimstep, yet deploys deep enough in the water for a clean prop bite. Problem solved.


Stainless Steel Outboard Motor Brackets

Designed with wide track stainless steel bodies for greater stability. The ability to adapt an installation for optimum motor performance is enhanced with built-in features such as +/- transom angle adjustments that eliminate the need for shims, up to 8 stainless steel springs to help counterbalance the motor’s weight, and a 4 position locking bar to provide for proper motor trim in changing water conditions.

- Easier to lift and lower – Stainless springs help counterbalance motor weight
- Transom mount locks and holds motor up or swings down for propulsion
- Built in transom angle adjustment allows optimum motor performance
- Fits all style motors – Extra Wide (11 1/2" 29cm) Black Poly Mounting Board for newer, wider style motor locking clamps
- 4 position locking height adjustment
- Stainless Mounting Hardware & instructions included
- Wide track body for added stability
- Made of tough 304 Stainless Steel
- MOUNTING PAD 2" thick x 11 1/2" wide (5 x 29cm). Designed to also accommodate the width dimensions of late model auxiliary outboard motors.


Stationary Outboard Motor Brackets

- STATIONARY OUTBOARD MOTOR BRACKETS and Parts for 2 - Stroke Motors

This Stationary model Motor brackets comes especially designed for trolling or auxiliary 2 stroke outboard motors up to 15 H.P. and up to 75 lbs. with fixed height mount. Stationary motor brackets comes packed with mounting Hardware, 304 Stainless brackets and Black Poly Mounting Board 1 1/2" (4cm).

In Garelick data set, you can found that they comes in three specifications of the model, the model using Vertical Transom Mount, Vertical Transom Mountwith adjustable +/- from 7 degree to 35 degree transoms and Horizontal Platform Mount Model.


- OUTBOARD MOTOR TILTER
- REPLACEMENT MTG PADS
- HEAVY DUTY MOTOR SAFETY CABLE
- MOTOR BRACKET EXT. SHIMS
- ADAPTER PLATE FOR ALUMINUM BRCKETS.
- CANOE MOTOR BRACKET
- ADJ. ANGLE BRACKETS


EVAL line of outboard Brackets

Bracket model for auxiliary motor (outboard)

Anodised Alluminium bracket with wooden surface
available models, weight 40kg (length:22cmxWidth:13,5cm)

Bracket for auxiliary outboard-motor

Anodised Alluminium bracket with white plastic surface
available models, weight 40kg (length:22cmxWidth:13,5cm)...more >>

Armstrong Outboard Motor Brackets

Armstrong Nautical Products offers the finest Outboard motor Brackets

The effect of the extension of the boat hull below the waterline optimizes the performance of powerful 4-Stroke outboards. Increased Functional Space,Resale Value, Perfomance and Fuel Economy, efficiency means and better handling and lower fuel consumption.

Armstrong Products designs and construct


three series of brackets for Heavy Duty Applications:

Tournament Motor Brackets

Designer Motor Brackets

2000 Motor Brackets

Tournament(300 plus Horsepower per Outboard), Designer (designed for 2 Engines 300HP Max)and 2000 Series (250 plus Horsepower per Outboard) Brackets matched to your OutBoard horsepower and for both:boat and motor combination.

Patented Armstrong's Watertight Compression Deck Plate insures maximum flotation and provides instant access for Outboard inspection and insures maximum flotation. Designed construction from Marine grade aluminum provides the corrosion resistance needed for long Deck Plate life.

contacts:

Armstrong Nautical Products
3140 S.E. Dominica Terrace
Stuart, Florida 34997

web:www.armstrongnautical.com

Cheata Outboard Motor Brackets

With light weight Cheata Motor Brackets all controls of engine and lift mechanism are easily accessible,your Outboard can easily be cleaned.

Motor Brackets are designed from (Amalg-35, 6061)aluminum and tested to stress limits of over 200 pounds, come with One Year Limited Warranty.

-Cost of getting out an Inlet against an incoming tide,
-Getting out of your canal against the wind,
-Navigating under a draw bridge against wind and tide,
-Navigating a Harbour amongst many anchored boats,
-Getting home safely at the end of a calm day.....

contacts:

Cheata Outboard Motor Brackets
P.O. Box 1234
Hobe Sound, Florida 33475

tel: 1-561-346-8055

http://cheatabrackets.com/

Hernco

Fiberglass Transom Motor Brackets

Outboard Transom Brackets are made from Fiberglass reinforced plastic also high quality molde motor Brackets with a maximum floatation design. Both Models Single or twin motor Brackets are designed for use with 25" shaft length motors available with a 24", for standard Single Outboard 30", or 36" setback.

Custom modifications:
Custom modifications or colors,such as irregular transoms are available for charge upon order.

contacts:

861 N.E. Dixie Hwy.
Jensen Beach, FL 34957

tel: (772) 225-6949

http://www.hermco.net/

ADVENTURE MARINE Motor Brackets

Adventure Marine Manufacturing and developing Quality marine products,motor brackets and accessories for over 30 years

Available Models of Motor Brackets

Model 3000 Outboard Motor Bracket
Dinghy Swivel Bracket

Motor Bracket(8 lbs) for inflatable boats and hard shell dinghys,two positions: 90 degree and 45 degree positions. The “swivel” motor bracket allows the boater to leave the outboard engine on the dinghy when raising the dinghy to a vertical position onto the swim step.


Model 3000 Bracket are constructed for single 2 or 4 stroke outboard (maximum - 100 lb, 9.9 HP).

Motor Brackets model 3000 are Constructed of marine grade aluminum and stainless steel fasteners along with a polypropylene (PP) Plastic, Outboard mount.

Model 6000

Dinghy Hauler Davits

Designed for (No gluing of fittings,Maximum weight 300 lb )Inflatables and Extensions. Easy installation Motor Brackets manufactured of marine grade SS plus electropolished for extra protection. Come with complete mounting hardware.


Recommended: inflatable tubes up to 16-17” diameter, “Holding lifting Lines” to cleats of inflatable vessel. Available Stand-offs in 18” x 24”, 30” and 36” lengths. For extra support for inflatable boat Support pads are 3” wide by 12” long.

Model 6000-18

Designed for hard shell dinghys and inflatable boats,no gluing of fittings, Maximum weight 300 lb Outboard.

Outboard Motor Brackets

3100 - Auxiliary Motor Bracket

Auxiliary motor bracket by Adventure Marine, constucted of marine grade aluminum and Polypropylene motor mount for both types - power or sailboats.
Brackets for two cycle or four stroke outboard engines to 60 lb , 8 HP.


Motor Bracket 14” long.
Mounting flange 8” wide , 7” high
weight 9 lb. 6 oz.

4100 - High Thrust Motor Bracket

Designed for both: without power or with power tilt option 20 HP,140 lb. power
outboards, for mounting on a transom. High grade marine aluminum 4100 Brackets welded inside and out with the built-in tilting device of the outboard engine is used to tilt the outboard back cleaning, maintenance and clear the skeg from water.

Weight 21 lb. 8 oz.
21 1/2 ” long, 12 1/2 ” wide

10000 - Step Motor Bracket

Bracket Model 10000 to suit installation of swim steps.

Swim Step Motor Bracket manufactured for 9.9 HP Outboards for mounting on a swim steps(2 above swim step).


Suitable Motor Bracket for outboard motors up to 140 lb maximum weight and 20 HP maximum.


12 1/2 ” wide x 7” high.
weight 11 lb. 12 oz.

contacts:

1467 Mustang Place, Port Coquitlam, BC, V3C 6L2
Tel: 604-945-BOAT (2628)
free: 1-888-669-4300

web:http://adventuremarinemfg.com/

Sea-DOG ALUMINUM Motor Brackets - Outboard Transom and Horizontal Mount Fixed Motor Brackets.

Fulton Outboard Motor Bracket

Boaters outlet

Saltwater Outboard Motor Brackets

Elevated position plus 4 adjustable running positions. Anodized aluminum alloy, Stainless steel springs. Made entirely of non-corrosive material for salt water use. 2" motor mount made from marine black polypropylene.

Freshwater Outboard Motor Brackets

Elevated position plus four adjustable running positions. Anodized aluminum alloy, Stainless Steel springs and cadmium plated bolts. 2" motor mount made from marine black polypropylene.


Recommended for fresh water use only.

Fulton Heavy Duty Outboard Motor Bracket

Rated to 30 hp Outboards. Made entirely of non-corrosive strong materials for salt water use. Stainless steel, Extra strength torsion springs designed to counter balance motor. Heavy duty U-channel construction for more stability. 2" polypropylene mounting board. Stainless steel fasteners. High tensile anodized aluminum alloy components. This bracket provides the additional clearance required with 4-stroke engines. Fulton MB1820 is designed for use with 9.9 h.p. 4-stroke engines.

Fulton Brackets are offered for sale by marinemanifold.com

Plastimo Outboard Brackets

Adjustable Motor Brackets


Adjustable Plastimo Outboard Motor Brackets are a high quality stainless steel product with a wooden pad (Marine quality plywood or Varnished type marine quality plywood). Available 7 models of Brackets for motors from 6HP to 20HP or 50kgmax weight.

Bracket height affects stability and clearance, and is an important specification to consider when choosing a unit. Also Outboard Brackets comes in height clearance from 165 mm to 355mm depending on model.

Adjustable Motor Brackets with plastic pads

Motor Brackets with plastic pads Model A

This A model Adjustable Bracket is designed from 316 stainles steel structure
with polypropylene pad with 45mm Thickness offered in 265mm height x 210mm width x 160mm pad base.

These adjustable version is constructed for outbord engines up to 10HP or 30kg max weight and and height clearance of 260mm.

Motor Brackets with plastic pads Model B


This B model Adjustable Bracket is designed from 304 stainles steel springs with plastic pad (have the same dimensions of model A) and is constructed for outbord engines up to 20HP or 50kg max weight. These versions help save space.

Adjustable Aluminum Motor Bracket

anodised Aluminum Outboard motor Bracket


This model Bracket is designed from 3 anodised Aluminum structure/springs with polypropylene pad with 45mm Thickness offered in 265mm height x 210mm width x 160mm pad base. These light version is constructed for outbord engines up to 20HP or 50kg max weight and height clearance of 265mm.


Aluminum Motor Bracket with wooden pads

Single Adjustable Brackets

Plastimo Single Motor Adjustable Bracket + wooden pad model A

model A Motor Bracket


This A model Bracket is designed from Double structure Anodised aluminium -
Reinforced springs with marine quality wooden pad with 42mm Thickness
offered in 300mm height x 375mm width x 335mm pad base. These adjustable version is constructed for 2 stroke engines from 9.9HP to 30HP or 70kg max weight and height clearance of 320mm.

Plastimo Single Motor Adjustable Bracket + wooden pad model A

model B Motor Bracket

These B,C models Brackets are designed from Anodised aluminium structure with Varnished marine quality wooden pad with 40mm Thickness offered in 270mm height x 270mm width x 200mm pad base. These versions is constructed for motors from 15HP to 20HP or 35kg max weight and height clearance of about 300mm.

Plastimo Single Motor Adjustable Bracket + wooden pad model A

model C Motor Bracket

Thise D,E models Plastimo motor Brackets are designed from Anodised aluminium structure with Varnished marine quality wooden pad.

Plastimo Single Motor Adjustable Bracket + wooden pad model A

model D Motor Bracket

Motor Bracket Model D comes offered in 300mm height x 300mm width x 270mm pad base. These versions is constructed for motors from 9.9HP to 30HP for 4 stroke motor or to 50kg max weight for 2 stroke motor and height clearance of 280mm.

Plastimo Single Motor Adjustable Bracket + wooden pad model A

model E Motor Bracket


Motor Bracket Model E comes offered in 270mm height x 200mm width x 200mm pad base. These versions is constructed for motors from 25HP to 40kg max weight for 2 stroke motor and height clearance of 320mm.

Custom modifications and colors such as irregular transoms or fitting to curved are NOT available upon request.

Plastimo Fixed Brackets

Strong non-corrosive designed from st. steel side plates with adjustable varnished ouiboard mounting pad.
Strong fastening to transom with 6 screws. Constructed for 4hp motors or 15kg max weight.

 Plastimo Fixed Brackets model 001


Console designed from st. steel. 0° to 17° Straight varnished marine wodd pad, adjustable in 3 positions, Strong fastening to transom. Designed for 8hp motors or 40kg max weight.

Plastimo Fixed Brackets model 002

Fastening to transom Plastimo Bracket model. Console made from st. steel, 22° to 35° inclined vamished marine wodd pad. adjustable in 3 positions. Fixed motor bracket version is Designed 8hp outboard engines or 40kg max weight.

plastimo.com

Trem Motor Brackets - A deep assortment of Fixed and Adjustable motor brackets

Outboard Motor Brackets, outboard jack plates & Motor Mount Accessories - installation advice, tips and guides